13
Oct 2025
Autotuner – Bosch MDG1 DDE8/DME8 2020+
REMOTE UNLOCK FOR BMW GROUP Yes, you read that right. Things are getting serious for Bosch MDG1 ECUs fitted from 2020 onwards across BMW platforms! 🚀 The DDE8 and DME8 versions, featuring the new Bosch protection, are now supported in BENCH after Remote Unlock, with your AT Tool: MD1CP032 – TC299 MD1CS001 – TC298 MG1CS024 – TC298 MG1CS049 – TC298 MG1CS201 – TC298 To use this service, make sure to verify your ECU’s eligibility by performing a BENCH identification. Once it is verified, you’ll need to ship your ECU to our headquarters for unlocking. The
New AT Protocol! 🏍️ Kawasaki is joining the race! The Denso SH7058 as well as Mitsubishi MH8115F and MH8610F ECUs are now supported with VR reading via OBD, using your AT Tool. 🔧 We are not slowing down on the two-wheel front. 🚀 Stay tuned to discover our upcoming new features! 🔥 Key Features Type: Engine Control Unit (ECU) ⚙️ Mode: OBD VR 🔌 Readout: Software + Calibration 🧩 MCUs: RH850, SH7058, SH72531 🖥️ Write time: 2min to 10min ⏱️ Checksums correction ✅ ⚠️ This
02
Oct 2025
Autotuner – Denso RH850/SH7058
New AT Protocol! 🏍️ Work continues on the two-wheel front! The Denso RH850 and SH7058 ECUs found in Yamaha models are now supported with VR reading via OBD, using your AT Tool. 🔧 ⚠️ These protocols require a specific cable depending on the vehicle’s production year: 👉 The Yamaha Euro4 OBD 4 Pin cable for models before 2020 👉 The Motorcycle Euro5 OBD 6 Pin cable for models from 2020 onwards Another compatibility to keep expanding our motorcycle
Flex OBD Support for Ford USA Bosch MDG1 ECUs OBD Connection for Ford USA Supported Vehicles Check all supported vehicles Ford F-150 XIV 3.5L 450PS Ford F-250 Super Duty V 6.8L 400PS Ford F-650 Super Duty VIII 6.7L V8 330PS Ford Bronco VI 2.3L EcoBoost 280PS Volkswagen Amarok II 2.3L TSI This new protocol is available for the following software packages: OBD OBD FLS0.1M – SW Flex ECU (car, van,
29
Sep 2025
CMD Flash – 3.2.0.272
NEWS VER 3.2.0.272 OBD Ford – Bosch MD1CS025 FULL OBD (for Ford Transit Connect/Courier,TOURNEO 1.5 ECOBLUE) This new OBD protocol allow you to manage the map and firmware areas of Bosch MD1CS025 ECU. The solution operates directly through the diagnostic port.
29
Sep 2025
Alientech – Kess3 – 2.44
29.09.2025 – Upgrade 2.44 With this update, you can quickly and safely work on Continental SIMOS16.1, 16.11 and 16.12 ECUs installed on Audi 3.0 TFSI engines produced from 2013 to 2015. Thanks to the Virtual Reading mode via OBD, you get the original files directly from the server and connect without opening the ECU, ensuring efficiency and reliability in the workshop. In addition, the protocol is also available on Powergate:
29
Sep 2025
Autotuner – Denso/Mitsubishi RH850 (Suzuki)
New AT Protocol! Our motorcycle coverage keeps growing! 🔥 The Denso RH850 and Mitsubishi RH850 ECUs found in Suzuki models are now supported with VR reading via OBD, using your AT Tool. 🔧 ⚠️ This protocol requires the Motorcycle Euro5 OBD 6 Pin cable, available on our website: 👉 Visit AT Shop Another addition that keeps expanding our playground on the two-wheel side. 🏍️ Stay tuned to discover our upcoming new features! 🔥 Key Features Type: Engine Control Unit (ECU) ⚙️ Mode: OBD VR 🔌
25
Sep 2025
Autotuner – Bosch ME17.0.3
New AT Protocol! A new release is now available for Bosch ME17.0.3 ECUs, now supported in OBD mode for Ford vehicles. 🚗 This protocol allows you to perform a real read (NR) directly through the OBD port, giving you immediate access to the ECU’s content. Stay tuned to discover our upcoming new features! 🔥 Key Features Type: Engine Control Unit (ECU) ⚙️ Mode: OBD NR 🔌 Readout: Calibration 🧩 MCU: TC1724 🖥️ Read time: 1min ⏱️ Write time: 30sec ⏱️
Bosch VD1CP110 Exclusive OBD Flex Version 7.33.0.0 and New StageX Update Ready With the release of Flex software version 7.33.0.0, OBD programming is now available for Bosch VD1CP110 control units, used in the management of AdBlue systems. In just a few minutes, you can now have direct access to the ECU calibration data through the diagnostic port, or, if the vehicle is not available, you can also proceed via the ECU connector. Supported Vehicles Check all
22
Sep 2025
Alientech – Kess3 – 2.43
22.09.2025 – Upgrade 2.43 It’s true, it took us a while. But with this release, KESS3 and Powergate allows you to work on 2.0 TSI and TFSI engines (from 245hp) of the VAG Group from 2018 to today. Manage reprogramming even on the most recent vehicles, directly from the diagnostic port, ensuring quick and safe operations in your workshop. An update that definitely expands your opportunities on iconic and in-demand
